Saniflo Sanicubic 1 VX Vortex 240v Simplex Vortex System (220-240V/60Hz) - 049

Product ID 049 SKU 049
Configure Product
Price:Choose option(s) to show price


The Sanicubic 1 VX is a 1.5 HP heavy duty simplex Vortex system used to pump away waste water from several bathrooms and fixtures from an entire building structure.
This system is able to discharge the waste up to 36 feet vertical and/or 328 feet horizontal using 2 in. pipe or up to 20 feet vertical and/or 1640 feet horizontal using a 4 in. pipe.
This lift station is ideal for uncontrolled environments in both residential and commercial applications (ie. rental unit, offices, warehouses, etc).
The Sanicubic 1 VX incorporates a vortex impeller capable of handling up to 2 in. solids.
Discharges the waste through either a 2 in. or 4 in. rigid pipe. A built-in non-return valve is included on the internal discharge pipe.
Has been designed with a 2-1/2 in. vent connection on the top of the enclosure. All plumbing codes require connection to a vent system. Please note that the vent system should be a two-way air vent as air needs to freely flow both ways. Note: The use of mechanical vents, air admittance valves or similar devices is not permitted.
The Sanicubic 1 VX is IP68 rated for possible submergence which eliminates any potential water damage to internal components. It comes equipped with an external control panel as well as a visual and audible alarm system (15 ft long wire).
The pump discharges wastewater from several toilets, sinks, bath/showers, urinals and even washing machines. The wastewater from other sanitary fixtures is drained into the Sanicubic 1 VX via three 1-1/2 in. or 4 in. inlets on either side of the housing and on top of the enclosure. Note that when draining waste water into the pump through either of the side inlets, an external check valve (not supplied) has to be installed. Also, note that there should be a minimum 11 in. height difference between the base of the Sanicubic 1 VX to the bottom of the shower/bathtub drain or to the base of the toilet.
System can be installed above the floor or inside a pit.
Pump Type: Vortex
Electrical: 220 240v - 60Hz / 12 amps (max)
Motor: 1.5 HP oil-filled thermally protected motor
Capacitor Rating: 30 microfarad
Operating Temperature: 158 degrees F
Power Cord Length: 98 in.
Noise level (measured at 3 ft): less than 70 dBa (Lp)
Discharge Pipe: 2 in. or 4 in. diameter
Discharge Rate at 36 ft (2 in.): 26 gpm / Discharge Rate at 20 ft (4 in.): 90 gpm
Discharge Rate at 3 ft: 2 in. - 125 gpm / 4 in. - 137 gpm
Shut-Off Head: 43 ft
Normal Running Time: depends on number of fixtures
Capacity: 15.9 gallons
Inlets: 1-1/2 in. or 4 in. (side) 1-1/2 in. or 4 in. (top)
Method of Activation: Pressure switch / circuit board
Shower/bathtub Base Height: 11 in. minimum
Connections: Toilet, sink, shower/bathtub, washing machines (direct connection), etc.
Certified by CSA (IPC, NSPC), IAPMO (UPC)
Dimensions: 19-7/8 in. x 27-5/8 in. x 21-5/8 in.
Weight: 68 lbs

PDF1
049 Sanicubic 1VX
PDF1
sanicubic 1vx instruction manual
PDF1
Sanicubic Brochure US
WARNING:This product can expose you to chemicals which are known to the State of California to cause cancer, to cause birth defects or other reproductive harm. Wash your hands after installing for uninstalling this product. For more information, go towww.P65Warnings.ca.gov.

Global Trade Identification Numbers (GTIN numbers) for this product. GTINs appear on barcodes and identify products sold by different retailers as the same product.

0859925002497